Guide for Configuring Cisco Catalyst WS-C2960-24PC-L Switch to Layer 2
Get to know the simple steps for professional configuration of the latest Cisco Catalyst 2960 series switch to layer 2 in your home or office network by reading this post.
On the off chance that you have to improve your network execution by superseding your old network hubs and need execution and consistent quality local segment level QoS (Quality of Service) and PoE (Power over Ethernet), by then the Cisco 2960 switch ought to be your top decision. On the off chance that you have as of late had 2960, by then you would try to improve your structure execution and sensibility. The WS-C2960-24PC-L shows up in a few models, with 8, 24 or 48 ports, supporting Fast Ethernet and Gigabit Ethernet. The 2960 switch is an ideal contraption for a self-ruling association or a branch office domain.
What You Require for Configuring WS-C2960-24PC-L Switch
Here are the things which you require for brief design of WS-C2960-24PC-L switch to layer 2:
- IP address
- Subnet mask
- Telnet password
- Enable password
- Serial cable
- Enable secret password
- Computer with terminal emulation software
Basic Instructions to Proficiently Configure Cisco Catalyst 2960 WS-C2960-24PC-L Switch
Below are the essential instructions, which you need to follow to successfully configure Cisco 2960 switch to layer 2:
- Connect the switch to your PC with the blue sequential cable that ought to have been joined together with the switch. Associate the RJ-45 end of the link cable to the switch. This is the end that looks like a huge phone connector. Connect the 9-pin d-shell end of the link to your PC’s sequential port.
- Power on your PC and configure and set up a terminal connection to the switch. You can utilize anything that gives terminal copying, and there are a few free assignments open on the Internet, including CRT, Putty and HyperTerminal. Set the terminal link cutoff points to Xon/Xoff stream control, 9600 baud, 8 data bits, 1 stop bit and no correspondence.
- Power on the switch and search for the startup messages. Check your terminal link settings on the off chance that you don’t see the messages following a second or close. Be certain the terminal link settings are right.
- Proceed to the concealed configure dialog and significant service arrangement by accepting the defaults of “yes” at the prompts. You can perceive the defaults by fundamentally pressing “Enter.”
- Press “Enter” when prompted for the hostname to recognize the default of “Switch,” or enter another hostname and press “Enter.”
- Enter the enable secret password, and press “Enter.” Repeat this procedure for the enable secret phrase and the virtual terminal secret phrase. Try to record all of the three passwords and store them in a secure spot.
- In case you are affected about SNMP Network Management perceive the default by simply pressing “Enter.” Enter “vlan1” and press “Enter.” This will see the interface that will be utilized to associate with the service network.
- Enter “yes” when displayed to “Configure IP on this interface?” and press “Enter.” Enter the IP address for the switch and press “Enter.” Enter the subnet mask at the command prompt and press “Enter.”
- Enter “no” at whatever point prompted to “engage as a group order switch,” and press “Enter.” The switch will eventually be indicating the current setup, and you will be given three options.
- Enter “2” and press “Enter” to save the design to NVRAM and exit. Right when the switch comes back with its concise, you are done with the initial configuration for your WS C2960 24PC L switch.
In the event that you need a Cisco Access Switch that can make with your business, will be capably secure, be less irregular, be coherently quick, it must be Cisco 2960 series switches. The Cisco 2960 Catalyst WS-C2960-24PC-L series switches designs for any undertaking sort out. They are stacked Gigabit Ethernet Layer 2 and Layer 3 access changes to improve the game plan, researching, and the board. This switch, not just sponsorships computerized programming establishment and port design yet neighboring different hugeness sparing features to help you with decreasing costs.
The Cisco 2960 series switch is in addition worked in for network programmability. The new switches are Cisco onePK-organized – Cisco onePK is an easy to-use Cisco Software-Defined Networking (SDN) gadget stash for progress, computerization and speedy help creation. Considering being one-engineered, the Catalyst 2960 series switches engage customers to make applications to automate and make associations over the grounds, further expanding the endeavor security cutoff points of this new switch series by Cisco.
The Catalyst 2960 presents another first for the Catalyst 2K family: Layer 3 coordinating limit near to application-careful data, reasonably making it the “sharpest” switches in its family families. Cisco 2960-X approach switches are not hard to send, oversee and examine. As an enormous bit of Cisco’s Unified Access portfolio, the Cisco 2960 series switches are likewise totally got along with Cisco Prime for direct action from a central zone and Cisco Identity Services Engine (ISE) for improved One Policy the specialists. The switches can in like manner be coordinated by Cisco Network Assistant (CNA), which intertwines an instinctual GUI to allow customers to sensibly apply basic relationship across Cisco switches, access points and routers.
